tilers.tradePost a job

Guide

Can you tile onto floorboards or plywood?

Not straight onto floorboards: they flex and move, and the tiles and grout crack. Tiles go onto a stiff timber floor overlaid with exterior-grade plywood at least 15 mm thick, screwed at about 300 mm centres, or a tile backer board fixed to its maker's specification, often with an uncoupling membrane on top.

Updated

Illustration: a herringbone tile floor in perspective, running to a skirting board and a doorway

Why not straight onto floorboards?

Floorboards are made to give a little underfoot and to shrink and swell with the seasons, and the gaps between them open and close as they do. Tile, adhesive and grout are rigid. Put the two together and the movement shows up first as cracked grout lines running along the boards, then as hollow and cracked tiles. Boards also have nail heads, cupping and uneven joints that make a flat bed hard to achieve. So the boards stay as the structure, and a stiff, flat layer goes on top of them for the tiles to bond to.

Make the floor stiff first

Tiles are only as steady as the joists under them. Before any boarding goes down, the floor is checked for bounce: walk it, and look for joists that are undersized, notched deeply for pipes, or spanning further than they should. Loose boards are screwed down, squeaks traced, and soft or rotten timber replaced. Extra noggins (short timber braces) between the joists may be needed under a heavy bath or a run of large tiles. A floor that still bounces after boarding will crack tiles whatever goes on top, and large format porcelain is the least forgiving of all.

It is also the moment to look under the boards. Pipes and cables run between the joists, so mark where they are before any screws go in, and leave access to anything that may need reaching later, such as a joint in a pipe run. Once the floor is boarded and tiled, getting back to them means lifting tiles.

Plywood or backer board?

Plywood overlayTile backer board
What it isExterior-grade ply sheetsCement board, or foam with a cement or resin face
Thickness over boardsAt least 15 mmAs its maker states for floors
FixingScrewed at about 300 mm centresScrews and washers or adhesive, to the maker's spec
Stiffness addedA lotVaries by type; check the data sheet
Near waterPrimed, and tanked in a showerCement types tolerate water; still tanked in a shower

Chipboard and MDF-type boards are not a base for tiles on their own, because moisture makes them swell. Ply sheets are laid with their joints staggered and off the line of the board joints below, with a small gap at walls. The ply is primed as the adhesive maker says before tiling.

Uncoupling membranes

An uncoupling membrane is a thin plastic or fleece-backed mat bedded onto the ply or backer board with adhesive and tiled directly. It lets the timber below move slightly without passing the strain up into the tiles, and some types double as a waterproof layer. It does not stiffen a bouncy floor; that still has to be fixed underneath. Many tilers use one on timber as a matter of course, especially under porcelain and large tiles, and the membrane's maker states what base and board thickness it needs.

Height, doors and thresholds

Ply, membrane, adhesive and tile together can add a surprising amount of height. Measure the build-up before choosing: doors may need trimming, a threshold strip is needed where the tiles meet carpet or wood, and a WC or the kitchen plinths may need resetting. An electric heating mat sits inside the adhesive layer and adds little. On a ground floor with a suspended timber floor, keep the airbricks clear, because the void under the boards needs its ventilation.

Bathrooms and kitchens

In a bathroom, the ply or board under the shower area gets the waterproofing that area needs, and the bath or tray goes in before the walls are tiled. In a kitchen, decide early whether the floor tiles run under the units, because the boarding then has to run under them too. Both are routine for bathroom tiling and kitchen tiling.

What to ask a tiler

  • Will you check the joists and deal with any bounce before boarding?
  • Plywood or backer board, how thick, and how will it be fixed?
  • Will you use an uncoupling membrane, and which adhesive goes with it?
  • How much height will the build-up add at the door?
  • Is taking up the old floor included? In a house built before 2000, old vinyl and black adhesive are tested for asbestos first.

Laying the ply or backer board is usually priced alongside the floor tiling labour, which the cost guides we use put at £15 to £50 per m², so ask for it as a separate line. The tile calculator works out the tiles.

Common questions

Can you tile over floorboards?

Not directly. Once the floor is stiff, overlay the boards with exterior plywood at least 15 mm thick, screwed at about 300 mm centres, or a backer board fixed to its maker's specification.

What thickness of plywood do I need for floor tiles?

At least 15 mm exterior-grade plywood over existing boards. Thicker ply, or ply with an uncoupling membrane, is common under large or heavy tiles.

Is backer board better than plywood?

Neither wins everywhere. Ply adds stiffness; cement backer board copes better with water. On timber floors many tilers use ply with an uncoupling membrane on top.

Do I need an uncoupling membrane?

Not always, but it lowers the risk of cracks from timber movement and is common under porcelain and large tiles on timber. It does not fix a floor that bounces.

Where to go from here

Tilers by county

Read next

Find a tiler near you