tilers.tradePost a job

Guide

Porcelain vs ceramic tiles: what is the difference?

Porcelain is a ceramic tile made from a finer clay fired harder, so it absorbs 0.5% of its weight in water or less and suits floors, showers and outdoors. Standard ceramic is softer and more porous, lighter, cheaper and easier to cut, and suits walls and light-use floors indoors.

Updated

Illustration: large porcelain slabs with thin joints on a floor and wall, levelling clips in the joints and a suction lifter

What makes a tile porcelain

Both are ceramic in the broad sense: clay pressed into shape and fired in a kiln. Porcelain uses a finer, denser mix fired at a higher temperature, which leaves a body that is hard and almost non-porous. The European standard for ceramic tiles, BS EN 14411, groups pressed tiles by how much water they absorb, and porcelain sits in the lowest group, BIa, at 0.5% or less by weight. Ordinary ceramic wall tiles sit in a far more absorbent group. The group is printed on the box or the maker's data sheet, and that is the reliable way to tell them apart, because a glazed porcelain and a glazed ceramic can look identical on the shelf.

The differences that matter

PorcelainCeramic
Water absorption0.5% or lessHigher, often much higher
Hardness and wearDense, resists chips and wearSofter body under the glaze
WeightHeavier for its sizeLighter
CuttingNeeds a good cutter or a wet sawScores and snaps easily
OutdoorsFrost-resistant grades madeUsually indoors only
ColourFull-body types run right throughColour sits in the glaze
PriceUsually higherUsually lower
Illustration: a herringbone tile floor in perspective, running to a skirting board and a doorway
A herringbone floor running to a doorway: on a floor that takes daily traffic, porcelain's harder body earns its price.

Glazed, full-body and rectified

Three words on the box are worth knowing. Glazed porcelain has a printed or coloured glaze over a porcelain body, which is how most stone-look and wood-look tiles are made; a deep chip shows the plainer body colour underneath. Full-body porcelain carries its colour right through, so wear and chips show less, which suits heavy-use and commercial floors. Rectified tiles, porcelain or ceramic, are ground to an exact size after firing, so they can take narrower joints; tiles that are not rectified vary slightly in size and need a wider joint to absorb the difference.

Where porcelain is the right choice

Floors, especially kitchens, hallways and anywhere chairs are dragged or traffic is heavy: porcelain wears better, and a chip in a full-body porcelain shows the same colour beneath. Shower floors and wet rooms, where low absorption matters. Outdoors, where only a tile its maker states is frost resistant should go; porcelain paving for patios is often 20 mm thick and laid on a mortar bed, not tile adhesive. And large format tiles are almost always porcelain, because only a dense body is strong enough to be made in big, thin sheets.

Where ceramic makes sense

Ceramic is lighter, cheaper and far easier to cut and drill, which makes it the sensible choice for most walls: splashbacks, bathroom walls and feature walls, where nothing walks on it and the load on the wall matters. Many handmade and decorative glazed tiles, metro and zellige styles among them, are ceramic. Plaster and plasterboard have a weight limit for tile and adhesive together, and lighter ceramic leaves more margin; see tile weight limits. A ceramic tile sold as a floor tile is fine in a bathroom or bedroom with light use, but check the box says it is rated for floors.

Slip resistance is a separate question

Neither material is grippy or slippery in itself: the surface finish decides it. A polished porcelain can be slippery when wet, a matt or textured one much less so. HSE uses the pendulum test to measure how slippery a floor is, and classes a pendulum test value (PTV) of 36 or more as low slip potential. Many tiles are sold with an R rating instead, R9 to R13, from a German ramp test that HSE has reservations about, because it uses safety boots and oil rather than ordinary shoes and water. For a bathroom, kitchen or outdoor floor, ask the supplier for the tile's wet PTV.

What it means for fitting and cost

Porcelain changes how the tiles are fitted. It needs a flexible cement-based adhesive rather than ready-mixed tub adhesive, because its dense back gives a basic adhesive little to grip, and floors need full adhesive cover with no hollow spots. It is slower to cut, and holes need diamond bits; the guide to cutting tiles covers the tools. So a tiler may price large porcelain higher per m² than small ceramic. The cost guides we use put labour at £15 to £50 per m² for floor tiling and £20 to £50 per m² for wall tiling; ask whether a quote assumes the tile you have chosen. The tile calculator works out how many to order, and bathroom tiling covers a whole room.

Common questions

Is porcelain better than ceramic?

For floors, wet areas and outdoors, usually, because it is harder and absorbs almost no water. For most walls ceramic does the job as well, and it is lighter and cheaper.

Can you use ceramic tiles outside?

Usually not. Most ceramic absorbs enough water to crack when it freezes. Use a tile its maker states is frost resistant, which in practice means porcelain.

How can I tell if a tile is porcelain?

Check the box or data sheet for its water absorption group: porcelain is group BIa under BS EN 14411. A full-body porcelain also shows the same colour on a chipped edge as on its face.

Can porcelain tiles go on walls?

Yes, and they are common in showers. Check the wall can take the weight, use a flexible cement-based adhesive, and expect cutting to take a tiler longer than ceramic.

Where to go from here

Tilers by county

Read next

Find a tiler near you