tilers.tradePost a job

Guide

How to remove floor tiles and wall tiles

To remove floor tiles, break one out with a club hammer and bolster, then lever the rest up from that gap at the adhesive line and scrape or grind the old adhesive flat. Wall tiles come off the same way but often take plaster or board with them. Have old vinyl or thermoplastic tiles tested for asbestos first.

Updated

Illustration: a floor with tiles being lifted, adhesive ridges on the screed, broken pieces and a long-handled floor scraper

Before you start: what is coming up?

Check what the tiles are. Ceramic, porcelain, quarry and stone tiles are not asbestos materials. Old vinyl or thermoplastic floor tiles, often 9 inch squares, and the black bitumen adhesive under them may contain asbestos in a home built or refurbished before 2000, so have them tested before anything is disturbed; the guide to asbestos in old floor tiles explains the route. Ask, too, whether the tiles need to come up at all: sound, flat tiles can sometimes take new tiles on top, as tiling over old tiles explains.

Then find out what is underneath. A concrete screed survives a hammer and bolster; timber boards and plasterboard do not, and the method changes with them.

Tools and protection

  • A club hammer and a wide bolster chisel, or a long-handled floor scraper for larger areas
  • An SDS drill (a heavy-duty hammer drill) with a wide chisel or tile-lifting bit, which saves hours on a floor
  • Safety glasses, heavy gloves, knee pads and stout shoes, because broken tile edges are sharp
  • A properly fitted FFP3 dust mask, with water or extraction to keep dust down at the source
  • Strong rubble sacks, and a plan for getting rid of them

Breaking tiles and grinding adhesive makes dust containing crystalline silica, which HSE treats as a serious risk to the lungs. Keep the work damp where you can, vacuum with a suitable extractor rather than sweeping, and close the room off from the rest of the house.

Illustration: a herringbone tile floor in perspective, running to a skirting board and a doorway
A finished floor running to the skirting: whatever comes up has to leave a base flat and sound enough for a floor like this.

Removing floor tiles step by step

  • Clear the room, and take off skirting boards or door bars that trap the edge tiles.
  • Find a cracked or loose tile, or break one out in the middle of the floor with the hammer and bolster.
  • From that gap, drive the bolster or SDS chisel under the next tile at a low angle, at the adhesive line, and lever it up. Work along a row, then start the next.
  • Bag broken tile as you go: a floor of tile and adhesive weighs far more than it looks.
  • Scrape or grind off the adhesive until the floor is flat enough for whatever goes on next.

If the floor has an electric heating mat in it, switch it off at the controls first; the mat will not survive the tiles coming up.

Removing wall tiles and protecting the wall

Wall tiles usually sit on a thinner bed, so a bolster slid behind each tile at the grout line will often pop it off. Start at the top row or an open edge, rake the grout out first if the tiles are tight, and work slowly. The plaster or plasterboard behind is softer than the adhesive, so some damage is normal: expect patches of plaster to come away, and on plasterboard expect the paper face to tear.

Do you need to replaster after removing tiles? Small blown patches can be filled and primed. Large areas of loose plaster, or plasterboard that is torn or soft, are usually better cut out and replaced or lined with new board, because new tiles need a sound, flat background. In a shower, look hard at what was behind: damp board or no waterproofing means the area needs tanking before it is tiled again.

Getting the old adhesive off

On a concrete floor, adhesive ridges come off with a scraper, an SDS chisel or a grinder with a diamond cup wheel and a dust shroud; grinding is the dustiest step of the whole job. The aim is a flat, clean, sound surface, not bare concrete everywhere. Where the screed is gouged or uneven, a levelling compound brings it back. A timber floor with tiles stuck straight onto the boards is often quicker to cover with new boards than to scrape; see tiling over floorboards.

Getting rid of the rubble

Broken tile and adhesive are heavy and bulky. Many council recycling centres take a limited amount of DIY rubble, but the rules and any charges vary by council, so check before loading the car. If someone else takes it away, the law puts a duty of care on you as the householder to give it only to a registered waste carrier: in England you can look them up on the Environment Agency's public register before handing it over, and ask for a receipt.

When to get a tiler in

A small splashback is a fair DIY job. A whole floor, a screed that must stay intact, or walls that will be retiled straight after are where a tiler's kit and practice save days. Checkatrade's 2026 removal guide puts lifting a ceramic floor at about £13 per m² on average; see tile removal costs. Many tilers include removal in a floor tiling or bathroom tiling quote, so ask for it as its own line.

Common questions

What is the easiest way to remove floor tiles?

An SDS drill with a wide chisel bit, driven under each tile at the adhesive line from a gap you have broken out. A club hammer and bolster does the same job more slowly.

Can you remove tiles without breaking them?

Rarely, once they are bedded in modern adhesive. If you need to save a few, cut out the grout all round first and work them up slowly from the bed, and expect to lose some.

Do I need to replaster after removing wall tiles?

Often for part of the wall. Small patches can be filled; large areas of loose plaster or torn plasterboard are cut out and replaced, or covered with new board, before new tiles go on.

Can I take old tiles to the tip?

Many council recycling centres take a limited amount of DIY rubble, sometimes for a charge. Check your own council's rules before you go.

Where to go from here

Tilers by county

Read next

Find a tiler near you